HOME / NEWS / Industry News / What Is the Best Lift for Uneven Ground and What Are the Alternatives to Using a Scissor Lift

Industry News

What Is the Best Lift for Uneven Ground and What Are the Alternatives to Using a Scissor Lift

Equipment Selection Report

Vertical Mast Lifts on Uneven Ground: What is the best lift for uneven ground and What are the alternatives to using a scissor lift?

Ground slope, floor loading, doorway width, working height and platform capacity form a five-variable equation. Vertical Mast Lifts solve one part of that equation that scissor lifts structurally cannot. This report breaks the equation down into measurable values.

Reading time: 18 minutes Category: Aerial Work Platforms Format: Technical Reference
0.76–0.82 m
Stowed width across the Vertical Mast Lifts range
1.7–2.0 m
Stowed height, clearing standard doorways and passenger lifts
160–230 kg
Platform capacity, one to two operators with tools
25%
Gradeability on tracked Vertical Mast Lifts, approximately 14°

What is the best lift for uneven ground? The question arrives from job sites where the concrete has not been poured, where the slab has a fall for drainage, where the yard surface is compacted gravel, or where a loading dock creates a step that no wheeled chassis can climb. The answer is not a single model number. The answer is a set of threshold values that eliminate certain machine categories and leave the workable options standing.

Vertical Mast Lifts occupy a specific position inside that elimination process. They are not a universal replacement for every scissor lift application. They are a structural alternative that changes the ground contact logic, the footprint logic and the deployment sequence. Understanding where that alternative applies requires looking at why scissor lifts behave the way they do on non-level surfaces.

Why ground conditions eliminate equipment categories before height is even discussed

A scissor lift raises its platform by extending an X-shaped set of hinged arms. The geometry of that motion means the chassis footprint grows as the platform climbs. Stability comes from the width of that growing base. Remove the level surface and the entire stability model changes. The machine is no longer supported by a predictable contact patch. It is supported by whatever the ground happens to be doing underneath each wheel or each outrigger pad.

Manufacturers publish slope limits for a reason. A typical electric scissor lift is rated for operation on surfaces within 2° to 3° of level. Outrigger-equipped models extend that figure to roughly 5°. Beyond that range, the onboard tilt sensor either prevents elevation or the machine becomes genuinely unsafe to operate. The sensor is not being conservative. It is reflecting the physical reality that a raised scissor stack transfers load in a direction that a sloping surface cannot reliably resist.

Threshold value. A 3° slope across a 1.2 m chassis footprint produces a height differential of roughly 63 mm. That is enough to shift the centre of gravity of a raised scissor stack outside the stable support polygon on some configurations. The same 3° slope across a 0.80 m mast chassis produces approximately 42 mm of differential, which an outrigger levelling system absorbs without difficulty.

Manually cribbing a scissor lift to create a level base is a practice that appears on job sites. It introduces a new set of variables. Timber packs compress. Packing material shifts under load. The person installing the packing is working underneath or beside a partially raised machine. The labour cost of cribbing a single setup can exceed the rental differential between equipment categories. What are the alternatives to using a scissor lift? One of the most practical answers begins with removing the need for cribbing altogether.

The structural logic inside Vertical Mast Lifts

Vertical Mast Lifts invert the scissor lift's expansion model. Instead of spreading outward, the lifting mechanism extends upward through nested mast sections. Each section slides inside the one below it. The chassis footprint at ground level stays constant through the entire elevation cycle. Nothing about the machine's ground contact changes between the stowed position and the maximum working height.

That single structural difference cascades into a series of operational consequences.

01
Constant footprint
The mast rises inside a fixed chassis envelope. Ground pressure distribution does not change as the platform climbs, which removes the load-transfer problem that makes scissor lifts sensitive to slope.
02
Outrigger levelling
Deployable outriggers with articulated foot pads establish a levelled support plane independently of the chassis. Extension spans of 1.65 m to 2.13 m create a wide stability polygon relative to machine mass.
03
Narrow access profile
A stowed width of 0.76 m to 0.82 m passes through standard doorways and into passenger lifts. Scissor lifts at comparable working heights generally require 1.2 m or more of clear width.
04
Low point loading
Machine mass across the Vertical Mast Lifts range sits between 810 kg and 1,060 kg. Distributed across four outrigger pads or a tracked undercarriage, ground bearing pressure stays within the limits of most finished slabs.

The mast sections themselves are extruded from aviation-grade aluminium profiles. The material choice is not cosmetic. Aluminium reduces the moving mass that the lift cylinder or chain system has to raise, which in turn allows a lighter chassis and lower ground pressure. The trade-off appears in the working height ceiling. Most Vertical Mast Lifts operate between 5 m and 12 m. Above 12 m, the mast section count and the resulting deflection under load make the configuration less practical than a scissor or boom alternative.

Platform stability note. Mast deflection at full height is measured in millimetres, not centimetres. For tasks involving precision fixing, conduit alignment or panel installation, the lateral sway figure matters more than the rated capacity figure. A 200 kg platform that moves 15 mm under a sideways push is more useful on a finish trade than a 400 kg platform that moves 60 mm.

Tracked undercarriages and the expansion of ground tolerance

Wheeled Vertical Mast Lifts handle slope through outrigger levelling. Tracked versions handle slope through the undercarriage itself. The distinction matters on soft, loose or broken ground where wheels lose traction before the outriggers ever make contact.

A tracked undercarriage distributes machine mass across a continuous contact patch rather than four discrete points. Ground bearing pressure drops accordingly. On compacted gravel, crushed stone, damp clay or sand, the tracked version keeps moving where a wheeled chassis digs in. Gradeability on current tracked configurations reaches 25%, which converts to roughly 14° of continuous incline. That figure is not a marketing number. It corresponds to the angle at which the drive motors can still deliver sufficient tractive force without the tracks slipping.

25%
Maximum gradeability, tracked models
14°
Equivalent continuous incline
3–5.7 m
Horizontal outreach on jib-equipped variants
1–2
Operator capacity across the range

Automatic pothole protection is a related feature on tracked Vertical Mast Lifts. The system monitors chassis attitude and adjusts the support state when the undercarriage encounters a depression or a raised edge. On a job site where the ground surface is a mix of compacted areas and loose patches, this kind of continuous adjustment prevents the machine from reaching an unstable attitude during travel rather than during elevation.

The tracked configuration also changes the surface damage profile. Steel or rubber tracks spread load over a larger area than pneumatic or solid tyres. On epoxy floor coatings, polished concrete or marble, the difference in surface marking is immediately visible. Facilities maintenance teams working inside occupied buildings tend to specify tracked or non-marking wheeled Vertical Mast Lifts for this reason alone.

Slope tolerance across equipment categories

The chart below plots relative operational suitability against ground slope for four machine categories. The curves are derived from published slope ratings and outrigger levelling ranges. The vertical axis represents a composite suitability score combining stability margin, setup time and required ground preparation.

Suitability vs. ground slope — four platform categories
100 75 50 25 0 0° 5° 10° 15° 20° 25° 30° Ground slope (degrees)
Scissor lift Wheeled Vertical Mast Lifts Tracked Vertical Mast Lifts Spider lift

The divergence between the scissor curve and the tracked mast curve begins at approximately 3°. By 8°, the scissor lift has effectively left the operational envelope while the tracked Vertical Mast Lifts platform retains more than 90% of its suitability score. The spider lift curve stays highest across the full range because its four independently levelling outriggers can establish a level plane on almost any surface, but that capability comes with a narrower platform and lower capacity ceiling.

What are the alternatives to using a scissor lift?

The question is asked by estimators, site supervisors and facilities managers who have run into the limits of scissor lift deployment. The answer is not a single substitute. It is a family of alternatives, each occupying a different position on the trade-off between reach, capacity, footprint and ground tolerance.

Primary alternative
Vertical Mast Lifts
Constant footprint, outrigger levelling, stowed width under 0.82 m. Reaches 5 m to 12 m with 160 kg to 230 kg of platform capacity. The strongest option when the constraint is access rather than area.
Height 5–12 m Width 0.76–0.82 m Capacity 160–230 kg
Reach alternative
Articulating boom lifts
Multi-joint folding arms allow the platform to travel over pipes, beams and parapets before positioning. Horizontal outreach beyond 10 m. Chassis dimensions generally exceed mast configurations, which limits passage through tight openings.
Height 12–20 m Outreach 8–12 m Capacity 200–230 kg
Slope alternative
Spider lifts
Four independently levelling outriggers establish a level plane on stepped or sloped ground. Stowed width 0.8 m to 1.2 m. Platform dimensions and capacity are the limiting factors. Single-operator tasks on irregular terrain are the core application.
Height 10–18 m Width 0.8–1.2 m Capacity ≤250 kg
Surface alternative
Tracked Vertical Mast Lifts
Combines the mast footprint logic with a tracked undercarriage. Gradeability to 25%. Reduced ground bearing pressure on soft or sensitive surfaces. Automatic pothole protection maintains attitude during travel.
Grade 25% / 14° Mass 810–1,060 kg Capacity 160–230 kg

A fifth option exists but is rarely the right answer on non-level ground. Single-person vertical personnel platforms mounted on forklift or telehandler carriages introduce a dependency on the host machine's own ground tolerance and add a separate set of load chart restrictions. They are not covered here because they fall outside the scope of self-propelled platform selection.

Parameter comparison across platform categories

The table below collects the figures that drive selection decisions. Values represent mainstream configurations rather than maximum or minimum extremes available in each category.

Parameter Vertical Mast Lifts Tracked Vertical Mast Lifts Scissor lift Spider lift
Working height 5–12 m 5–12 m 6–18 m 10–18 m
Platform capacity 160–230 kg 160–230 kg 200–680 kg ≤250 kg
Operator count 1–2 1–2 2–3 1
Stowed width 0.76–0.82 m 0.79–0.99 m ≥1.2 m 0.8–1.2 m
Slope tolerance Levelling outriggers, to ~5° Continuous to 25% / 14° 2–3°, to 5° with outriggers Independent outriggers, to 25%
Machine mass 810–1,060 kg 950–1,200 kg 1,800–3,200 kg 1,400–2,600 kg
Doorway passage Yes, standard doors Yes, wider openings Generally no Yes, standard doors
Horizontal outreach 3–5.7 m on jib models 3–5.7 m on jib models None, vertical only 5–9 m
Ground bearing pressure Low Very low Moderate to high Low
Setup time 2–4 minutes 2–4 minutes 1–2 minutes 5–10 minutes

Stowed width against working height

The horizontal bars below compare stowed machine width at representative working heights. The width figure determines whether a machine can reach the work position at all. A platform that cannot pass the doorway never gets to demonstrate its other capabilities.

Vertical Mast Lifts — 8 m
0.76 m
Vertical Mast Lifts — 10 m
0.82 m
Tracked mast — 10 m
0.99 m
Spider lift — 12 m
1.20 m
Scissor lift — 10 m
1.65 m
Scissor lift — 14 m
2.10 m

A 0.76 m stowed width passes through a 0.80 m doorway with 40 mm of clearance on each side. A 1.65 m width does not pass through any standard internal door. That single number often decides the equipment category before the discussion moves to working height or capacity.

Power systems and duty cycle considerations

Vertical Mast Lifts in current production run on three power architectures. Each carries a different implication for indoor use, shift length and maintenance interval.

Lead-acid battery
Lower acquisition cost. Requires ventilated charging areas. Typical duty cycle supports one full shift of intermittent elevation on an 8 m machine. Weight contributes to the overall machine mass figure and therefore to floor loading.
Lithium battery
Higher energy density per kilogram. Opportunity charging without memory effect. Shorter charge windows suit multi-shift deployment. The mass saving translates directly into lower ground bearing pressure, which matters on suspended slabs and mezzanine floors.
Mains electric
Continuous duty without battery changeover. Requires a power drop within cable reach of the work position. Common in fixed installation and maintenance environments where the machine stays in one building.

Duty cycle calculations should account for the fact that mast elevation draws less current per metre of lift than scissor elevation at comparable heights. The mast raises a smaller moving mass. On a job site where the platform cycles up and down 40 times in a shift, that difference shows up in battery state of charge at the end of the day.

Floor loading and structural interfaces

Ground conditions include the surface being worked on and the structure beneath it. A mezzanine floor, a suspended slab or a raised access floor introduces a load limit that has nothing to do with slope but everything to do with whether a machine can be positioned there.

Vertical Mast Lifts distribute mass across four outrigger pads or a tracked contact patch. On a machine weighing 950 kg, static load per outrigger pad is approximately 238 kg before any dynamic factor. Adding a 200 kg platform load and two 80 kg operators changes the distribution depending on platform position, but the peak pad load generally remains below 400 kg. A scissor lift of comparable height weighs two to three times as much and concentrates that mass across four wheels or two wheel pairs plus a chassis.

Structural check. Suspended slabs in commercial buildings are frequently rated between 3 kN/m² and 5 kN/m² for live load. A 950 kg mast machine on four 200 mm × 200 mm pads produces roughly 58 kPa under each pad, well inside that range. A 2,800 kg scissor lift on four wheels with smaller contact patches can exceed the same limit depending on wheel size and load distribution.

Raised access floors present a different problem. The floor panels themselves are not structural in the same way as a slab. Point loads from outrigger pads can exceed panel ratings even when the overall machine mass is low. Spreading plates under the pads distribute the load across multiple panels and multiple pedestals. Tracked Vertical Mast Lifts avoid the issue entirely because the track contact area is continuous rather than point-based.

Safety systems that change with the platform category

The safety architecture of a Vertical Mast Lifts platform reflects its operating envelope. Because the machine is designed to work in tighter spaces and on less predictable ground, the sensor and interlock package differs from a scissor lift's.

Tilt sensing and elevation lockout
Chassis-mounted tilt sensors prevent elevation beyond the rated slope. On outrigger-equipped models, the interlock releases only after all four outriggers have made firm contact and the levelling system has confirmed a stable plane.
Pothole protection
Deployed automatically during elevation on tracked models. The system reduces the ground clearance beneath the chassis so that the machine cannot tip if a wheel or track section drops into a depression.
Mast chain or cylinder monitoring
Redundant load paths on the mast extension mechanism. In the event of a primary lift component failure, a secondary mechanical path holds the platform in position rather than allowing uncontrolled descent.
Platform load sensing
Overload detection prevents elevation beyond the rated capacity. Because the platform is small, the margin between rated capacity and actual load is easier to assess than on a wide scissor platform where load distribution across the deck is less predictable.
Emergency lowering
Manual descent valve accessible from ground level. On battery-powered models, an auxiliary power unit provides controlled descent if the main power source is depleted or isolated.
Guardrail and gate interlock
Entry gates on the platform are mechanically interlocked with the control system. Elevation is not possible with a gate in the open position. Guardrail height and toe board dimensions follow the applicable regional standard.

Selection framework: matching machine to measured conditions

What is the best lift for uneven ground? The answer emerges from four measurements taken before any machine is specified. Each measurement eliminates part of the available equipment population.

Measurement 1
Ground slope in degrees
Below 3°: any category remains viable. Between 3° and 5°: outrigger-equipped Vertical Mast Lifts or spider lifts. Between 5° and 14°: tracked Vertical Mast Lifts or spider lifts. Above 14°: spider lifts with extended outriggers or site preparation before equipment delivery.
Measurement 2
Narrowest access point in metres
Below 0.85 m: Vertical Mast Lifts only. Between 0.85 m and 1.2 m: mast or spider configurations. Above 1.2 m: scissor lifts become accessible. The access point includes doorways, lift interiors, gate openings and any temporary structure along the route.
Measurement 3
Working height and task duration
Below 10 m with intermittent tasks: Vertical Mast Lifts. Between 10 m and 12 m with extended tasks: evaluate platform size against task requirements. Above 12 m: scissor, boom or spider categories depending on access and ground conditions.
Measurement 4
Floor or ground bearing limit in kPa
Above 60 kPa: most categories viable. Between 30 kPa and 60 kPa: Vertical Mast Lifts, tracked models or spider lifts with spreader plates. Below 30 kPa: tracked models with spreader plates or site-specific engineering assessment before deployment.

The four measurements interact. A site with a 6° slope and a 0.80 m access route eliminates scissor lifts on both counts and points directly to tracked Vertical Mast Lifts or a spider configuration. A site with a 2° slope but a 0.75 m access route eliminates scissor lifts on access alone and again points to mast configurations. Two different constraints can produce the same equipment category, which is why the selection framework works from measurements rather than from equipment preference.

Deployment sequence on a non-level site

The sequence of operations matters as much as the machine specification. A tracked Vertical Mast Lifts platform deployed in the wrong order on a sloped site can end up in a position where it cannot be levelled or where the outriggers cannot reach firm ground.

1
Route survey before machine arrival
Walk the entire travel path. Measure the narrowest point. Identify any surface transitions where track or wheel contact changes. Note drainage falls, expansion joints and temporary covers that may not support machine mass.
2
Position selection with outrigger reach in mind
The work position must allow full outrigger extension within the available footprint. On a narrow mezzanine, this may mean positioning the chassis with the mast off-centre relative to the work point and using the jib or platform rotation to reach the task.
3
Levelling and confirmation
Deploy outriggers in sequence according to the manufacturer's procedure. Confirm firm contact under each pad. On tracked models, verify that the automatic pothole protection system has deployed and that the tilt indicator is within the permitted range.
4
Test elevation before loading
Raise the platform to full height without operators or tools. Observe mast behaviour under no load. Check for unusual deflection, noise from the mast sections or movement in the outrigger pads. Lower and re-check levelling before allowing access.
5
Load and work
Enter the platform, close the gate and confirm the interlock. Raise to working height. Keep tools and materials within the platform guardrails. On a sloped site, avoid leaning over the guardrail to extend reach in the downhill direction.

Applications where Vertical Mast Lifts replace scissor lifts outright

Certain job profiles map almost directly onto the mast platform's capability set. In these applications, specifying a scissor lift adds cost and risk without adding capability.

Interior fit-out with narrow corridors
Ceiling grid installation, lighting replacement, sprinkler adjustment and partition fixing in occupied buildings. The machine travels through the same doorways as the trades and does not require corridor closures.
Facade and cladding touch-up
Spot repairs on external walls where the ground is a mix of paving, gravel and planting beds. Tracked models move across the transition without needing a prepared surface at each position.
Warehouse racking maintenance
Aisle widths in high-density storage frequently fall below the minimum for scissor lift travel. Mast platforms pass through the aisle and elevate alongside the rack face without blocking adjacent aisles.
Atrium and multi-level void access
Suspended slab edges, balustrade fixing and high-level cleaning where the floor finish cannot accept wheel loading. The low point load profile keeps the machine within slab ratings.
Outdoor event and temporary structure work
Grass, gravel and temporary trackway surfaces. The tracked undercarriage handles soft ground and the mast footprint allows positioning close to stage edges and rigging points.
Plant room and service riser access
Pipework, valve and control panel maintenance in spaces where a scissor lift cannot enter. The platform reaches over equipment without the chassis needing to occupy the same footprint.

Maintenance intervals that affect total deployment cost

Machine selection decisions increasingly account for the maintenance burden across the ownership period. Mast platforms and scissor platforms present different service profiles.

Mast section wear pads are the primary consumable on a Vertical Mast Lifts platform. These pads guide the sliding interfaces between mast sections. They are accessible without major disassembly and are replaced on an interval measured in hundreds of operating hours rather than years. Chain systems, where used, require lubrication and tension checks at similar intervals. Hydraulic systems on mast machines operate at lower fluid volumes than scissor systems at equivalent heights because the lift cylinder stroke is shorter and the mast does the height multiplication mechanically.

Scissor lifts present a different service profile. The scissor arm pivot pins, bushings and hydraulic cylinders carry the full load of the platform and the arm structure itself. Wear on these components shows up as platform drift, uneven elevation or hydraulic seepage. The service access required to replace pivot bushings on a large scissor stack is substantially more involved than replacing mast wear pads.

Mast platform service items
  • Mast wear pads and guide blocks
  • Lift chain tension and lubrication
  • Outrigger pad articulation points
  • Tilt sensor calibration
  • Battery state of health
  • Emergency lowering valve function
Scissor platform service items
  • Scissor arm pivot pins and bushings
  • Main lift cylinders and seals
  • Hydraulic fluid volume and filtration
  • Deck extension slide mechanisms
  • Wheel and steering system components
  • Levelling jack function and seals

The practical outcome is that a mast platform at 8 m working height carries fewer high-load wearing components than a scissor platform at the same height. That difference does not show up in the acquisition comparison but does show up in the five-year operating picture.

Operator training differences between categories

Familiarisation requirements differ between mast platforms and scissor platforms even where the same operator certification covers both. The differences come from the control layout, the levelling procedure and the travel characteristics.

Mast platform controls typically place elevation, outrigger deployment and travel functions on a single platform-mounted console or a dual ground/platform control set. The outrigger sequence is the element that requires the most attention during familiarisation. Operators who have only run scissor lifts are accustomed to a machine that is ready to elevate as soon as it is in position. A mast platform on outriggers requires confirmation that all four pads are loaded and the levelling system has completed its cycle before the elevation control becomes active.

Tracked models add a travel control dimension that wheeled machines do not have. Counter-rotation steering, track tension awareness and the behaviour of the machine on side slopes are all elements that require specific familiarisation. The automatic pothole protection system changes the machine's ground clearance during elevation, which can be disorienting to an operator who is not expecting it.

Familiarisation focus. The highest-risk moment in a mast platform deployment on uneven ground is the transition between travel mode and elevate mode. The machine is stationary, the outriggers are deploying and the operator's attention is divided between the ground conditions around the pads and the control console. Structured familiarisation on a level surface before moving to the actual work position reduces that risk substantially.

Frequently asked selection questions

Can a Vertical Mast Lifts platform work on a 10° slope?
A wheeled model cannot. The outrigger levelling range on standard wheeled configurations covers approximately 5° of chassis tilt. A tracked Vertical Mast Lifts platform rated to 25% gradeability can travel and position on a 14° slope, but the outrigger or chassis levelling system still needs to establish a level platform plane before elevation. On a continuous 10° slope, the tracked machine travels to position, then the levelling system compensates for the residual tilt within its adjustment range.
What is the best lift for uneven ground when the surface is also soft?
Soft ground and uneven ground together point to a tracked undercarriage. Ground bearing pressure is the controlling variable. A tracked Vertical Mast Lifts platform distributes mass across a continuous contact patch and maintains gradeability on surfaces where wheels lose traction. Spreader plates under outrigger pads provide additional distribution where the surface is soft but relatively level.
What are the alternatives to using a scissor lift for a two-person task at 9 m?
At 9 m with two operators, Vertical Mast Lifts remain viable if the access route is restricted and the ground is not level. Platform capacity on two-person mast models reaches 230 kg, which accommodates two operators and hand tools. If the task requires a larger working deck or material staging on the platform, an articulating boom or a scissor lift on a prepared surface may be required. The determining factor is whether the task can be completed from a compact platform or requires movement around a larger deck area.
Does a mast platform require a larger footprint than a scissor lift when set up?
The opposite is generally true. A scissor lift's footprint at ground level is the chassis, but the machine needs clearance around that chassis for the deck to overhang and for operators to access the platform. A mast platform's chassis is narrower and the outrigger footprint, while wider than the chassis, is typically smaller in total area than the clearance zone required around a scissor lift at comparable height.
How does wind loading affect mast platforms at height?
Mast platforms present a smaller sail area than scissor platforms because the platform itself is smaller and the mast structure is narrow. That reduced sail area translates into lower wind-induced moments at the chassis. Rated wind speed for outdoor operation varies by model and platform height, and the applicable figure should be confirmed against the machine's operating manual before any outdoor deployment.
Can a tracked mast platform operate on a finished interior floor?
Rubber-tracked models can, provided the floor is structurally adequate for the machine mass. Non-marking track options are available. The automatic pothole protection system reduces ground clearance during elevation, which means the track contact area remains the only part of the machine touching the floor. On highly polished or coated surfaces, the track path should be inspected after the first movement to confirm that no marking or scuffing occurs.
What is the best lift for uneven ground when the work position is also tight?
Tight work positions and uneven ground together narrow the field to Vertical Mast Lifts, tracked or wheeled depending on surface conditions, and spider lifts. The choice between them comes down to platform capacity and reach requirements. Mast platforms offer higher capacity and faster setup. Spider lifts offer greater slope tolerance and horizontal outreach at the cost of a longer setup sequence and a smaller platform.
How does setup time compare between mast and scissor platforms?
Scissor lifts are faster to set up on level ground because there are no outriggers to deploy. The setup time advantage disappears on uneven ground because the scissor lift requires surface preparation, cribbing or relocation to a level position. Vertical Mast Lifts require two to four minutes for outrigger deployment and levelling confirmation, but that time is consistent regardless of the ground conditions within the machine's rated slope tolerance.
Specification summary

Vertical Mast Lifts change the ground contact equation by holding the chassis footprint constant through the elevation cycle and using outrigger levelling to establish a stable plane. Tracked variants extend that capability onto soft and sloped surfaces with 25% gradeability and automatic pothole protection. Platform capacity ranges from 160 kg to 230 kg across working heights of 5 m to 12 m. Stowed width of 0.76 m to 0.82 m allows passage through standard doorways and into passenger lifts.

What is the best lift for uneven ground depends on four measured values: slope in degrees, narrowest access point in metres, working height in metres and ground bearing limit in kPa. What are the alternatives to using a scissor lift depends on which of those four values falls outside the scissor lift's operating range. The tracked Vertical Mast Lifts configuration covers the widest combination of those constraints within a single machine category.